ebi sukore

Just another Blogger Blog

The first thing that must be done when troubleshooting mouse

Mouse is a tool to facilitate the work in the application and make the settings. compared with using the keyboard. But several factors may be a mistake that causes the cursor so that it does not damage the road, can be seen below. Possibilities of mouse data cable that is in the mainboard does not match. pemasangn data cable from this there are two types of data on the cable conector serial mouse. Solution if the mouse cable is not the original you try to change the settings of the data cable conector tersebu. this possibility you can do to help the cause at the top. Conector interruptedly mouse can cause the mouse does not display the way, if the mouse is not stable conector should still be the way but I can not last long. possible solution of the problems that you may be able to do to overcome the causes of damage memantu above, namely the wedge with a folded paper. if this is considered extremely urgent or can replace with another conector. There is a possibility also in the mouse cable to drop out, usually near the ends of the dropouts in the mouse, if it is like the way the mouse will not be at all. Solutions to the problems that may be above you can do is, measure the cable with the mouse data with AVO meter, if the cable is found to drop out then you can replace it with another cable. if there is no possibility of any other damage. Damage to the mouse driver can also cause the mouse can not work. mdriver especially when the mouse is not suitable, although other drivers can be used, but the mouse will not provide the maximum results, or not normal. solutions to the problems above, you can do is to use the drivers that competible for all types of mouse.

Read More......

Only Move the Cursor Horizontal / Vertical

There is an error factor of factors that may cause a cursor so that only moving horizontal / vertical, and all of that can be learned the following. When the mouse is used for long periods can cause the sensor to become dirty or ball mouse can also participate in the collection of dirty by the thick dust, this can cause the mouse to move one direction, because the mouse movement jammed. o The solution is in the mouse there are one or two to open the mouse Cassing found naked in a mouse, the mouse with the roller clean warm water or alcohol, after a clean install again as they are. * Mouse movement in the set by a given photo transistor optocoupler light be a roller rotation, rotation of each roller will make the mouse movement up and down, left or right, if the sensor is not working then the mouse will be subject to the mouse movement. o The solution is to measure the cable data using AVO meters. sensor with two feet there is an optocoupler sensor that has three feet how to measure it the same as transistor. if found in one of two directions is broken, replace the sensor with the other.

Read More......

Mouse

mouse is a tool that serves as the input pointer to help the working keyboard. cursor form of the resulting pointer. using the mouse, we can place the cursor position in accordance with our desires, and when compared with the keyboard is much faster and easier. mouse IBM PC was introduced by year 1922, and many now use the PC mouse, because the microsoft windows were popular, many who use the PC mouse on the side of the keyboard. and the following are types of types of mouse

Read More......

keyboard the right treatment

Some of the factors that can help and extend the age of a device / peripheral do with the care / maintenance. some of which may help.

  1. Clean the keyboard with a special liquid to a computer every 1 month or 3 months.
2. Broom and clean the dust from the keyboard in the thick brush that you can use to cover the key path. 3. Do not smoke in the computer room, because cigarette smoke can cause your computer to be yellow. 4. Do not laying liquid near the keyboard, because it will overflow if water damage is the keyboard. 5. Remember the computer after closing the cover again with a PC that is available, in order to protect from dust. 6. Do not poke the button on the keyboard with a screwdriver during demolition. any keyboard can cause damage.

Read More......

Frst on the keyboard troubleshooting

Display Keyboard error
What you mean a PC, without using the keyboard. Although small and price is cheaper than the other. But this one is the peripherals that are very important in running an operation in the PC. used if the PC does not have a floppy disk drive you can still work, but if your PC does not use the keyboard you will not be able to run PC's. Damage to this first, the computer only to appear, but does not want to continue their activities and give the message "keyboard error ... cheksum CMOS failur ... press F1 to continue and del to setup". so intruksi you follow, your PC does not show the results as well as signs to continue. The error number of factors, which may be the cause of the damage so that the display is a keyboard error. 1. conector interruptedly keyboard can cause a message that appears on the screen keyboard error. * Solution o the problems that may help you to overcome the above problems, namely the wedge with the paper, if considered urgent conector can change before a new keyboard. 2. likely also be on the keyboard is a data cable to drop out. usually dropped out of the base conector. if it is not like the keyboard will be a way. * Solution o the possibility of the problems that you may be able to do to help overcome the causes of corruption in the top, with the data using the keyboard with the AVO meters. if they found that the data cable that have dropped out, then replace the cable with the other. but if not there may be damage to the other. 3. IC controler keyboard found on the keyboard to work comvert language code / digits that ASCI will be informed to the mainboard, with the appropriate button in the press. IC damaged if the keyboard does not will road. * Solution o If using a new keyboard, to replace the IC is not possible because the price of IC controler keyboard more expensive than buying a new keyboard. I love so suggestions to overcome the above problems is to replace with a new keyboard. 4. Sometimes does not match the estimates, all have been replaced but still error kevboard possibility is that the last rupture sekring on the mainboard with the keyboard
located
/ female socket, labeled FS1 or F1 or L1. This component serves to deliver voltages of 5V to the keyboard this component is small as a sekring flow divider, if this sekring dropout voltage and current will also drop out so the keyboard does not get the voltage to run its tasks. * Solution o to cause the above is to replace the component F1 (sekring) the other, and must be the same size, if sekring not have this then you can replace it with a resistor.

Read More......

kumpulblogger

Follow Me